Asp

NOTE: The ASP Wiki is currently UNDER CONTRUCTION

Welcome to the Asp Wiki Page. This site serves as the online manual for the Asp control board. For various reasons there is no printed manual as such for Asp. This page along with the Asp Forum Topic and the Asp Youtube Playlist serve as the online reference source for Asp.

What is Asp?

Asp is essentially a radio controlled quad motor controller designed for use in 1/16th scale tanks. HOWEVER, in reality Asp is flexible enough for use in halftrack vehicles, fully wheeled vehicles and even boats/watercraft. Use of Asp in non tracked vehicles is covered in an upcoming section. For now let's just concentrate on tanks.

From inception, Asp has been designed as a simple plug and play replacement unit for existing Heng Long and Taigen Tank control units. As the picture below shows Asp shares many of the same style connectors as found on Heng Long and Taigen tanks including the somewhat standard 8-pin turret connector.

Asp is controlled by hobby standard R/C signals and thus will require the use of a true R/C radio and receiver. To make use of all of the available features on Asp an 8 channel programmable radio is suggested. However as of September 15 Asp can now be controlled with both 4 channel and 6 channel radio setups. Asp is supplied with a special cable for connecting the receiver to the mainboard.

Asp Main MFU

The main Asp control unit

Receiver Connections 4 Channel Operation

Channel 1 Steering White
Channel 2 Throttle Yellow
Channel 3 Gun elevation & Weapons control Orange
Channel 4 Turret Green

Receiver Connections 6 Channel Operation

Channel 1 Steering White
Channel 2 Throttle Yellow
Channel 3 Gun elevation & Weapons control Orange
Channel 4 Turret Green
Channel 5 Switching Blue
Channel 6 Sound control Purple

Receiver Connections 7 Channel Operation

Channel 1 Steering White
Channel 2 Throttle Yellow
Channel 3 Gun elevation Orange
Channel 4 Turret Green
Channel 5 Switching Blue
Channel 6 Sound control Purple
Channel 7 Weapons Grey

ASP Terminology & General Radio Programming Basics

Since most users will be upgrading to a true hobby grade R/C system to use ASP a basic understanding of how this system work will be of great advantage. In particular knowing what is sent from the outputs of your receiver and how servos or control boards like ASP respond will help immensely. This is what will be concentrated on here.

When your receiver gets information from your radio it splits this information up into the individual channels and sends it onto your control board, ESC or servos. All this information consists of is a single 'on' pulse of between 1 and 2 milliseconds repeated every 20 milliseconds. It is simply the amount of time that the pulse is on that tells the servo or control board what to do. In the case of servos a pulse of 1 millisecond will send the servo fully left and a pulse of 2 milliseconds sends the servo fully right. A pulse of 1.5 milliseconds is exactly in the middle and hence the servo will move to the mid point or NEUTRAL position. Since 1.5 is a rather odd number to work with it is easier to refer to the neutral position as 0 even though it represents a pulse of 1.5 ms. Calling the neutral position 0% is somewhat better as it represents a zero amount of displacement left or right. The full extent of travel left may then be termed -100% and the full extent of right travel +100% . Thus a pulse of 1 ms becomes -100% and 2 ms becomes +100%. The instructions for ASP use this convention. The table below demonstrates how the various pulse width signal on CH5 control the functions of ASP.

Pulse Width (ms)	%	Start Function	Operational Function
1.00 - 1.20	-100	Engine Start 4	Headlight on/off
1.21 - 1.25 - 1.30	-50	Engine Start 3	Aux light on/off
1.31 - 1.50 - 1.70	0
1.71 - 1.75 – 1.80	+50	Engine Start 2	Smoke unit on/off
1.81 - 2.00	+100	Engine Start 1	Engine off/Tank shutdown

Consequently, the “ON” signal for Asp is referred to as CH5 +100%. This means that to turn Asp “ON” Asp is looking for a pulse of between 1.8 and 2 milliseconds on Channel 5. When such a pulse is received Asp will “turn on” . If CH 5 is then returned to the neutral position we can continue to use the channel to receive more commands. Likewise if CH5 is in neutral when the tank is powered up we can use the 100% signal as a switch to turn the tank on when it is desired to do so.

If you wish to use a radio other than a 9X or Taranis series radio you will need to refer to your own radio manual as to how to assign switches to channels and what values to output for a particular switch position.

In summary, to set up a switch on your radio to control a function on Asp you must: 1. Set one position of the switch to output a neutral signal (0% ie: around 1.5 ms) 2. Set the second position of the switch to output the desired activation signal To operate start with switch in position 1. Activate the desired function by moving switch to position 2 and then return the switch to position 1 (toggle).

This information is important if you are programming your own radio switches to control Asp. Remember, if you are using a 9XR series or Taranis radio all of the settings for Asp can be downloaded and transferred to you computer via (USB). It is al done for you :). Knowing the above will help you if you wish to change from the default ASP radio settings.

JUNO sound board for Asp

Details of the Juno sound board

Sound Lists

Below are lists of sounds for both Module A and B

Module A

FILE #	Module	Model	Name	Description
1	A	Model	EngStart-1	Engine Start Variant 1
2	A	Model	EngStart-2	Engine Start Variant 2
3	A	Model	EngStart-3	Engine Start Variant 3
4	A	Model	EngStart-4	Engine Start Variant 4
5	A	Model	Shutdwn-1
6	A	Model	Shutdwn-2
7	A	Model	Shutdwn-3
8	A	Model	Shutdwn-4
9	A	Model	ShutdwnB
10	A	Model	EngIdle-A
11	A	Model	MotionStrt
12	A	Model	Speed-a140
13	A	Model	Speed-b135
14	A	Model	Speed-c130
15	A	Model	Speed-d125
16	A	Model	Speed-e120
17	A	Model	Speed-f115
18	A	Model	Speed-g110
19	A	Model	Speed-h105
20	A	Model	Speed-i100
21	A	Model	Speed-j095
22	A	Model	Speed-k090
23	A	Model	Speed-l085
24	A	Model	Speed-m080
25	A	Model	Speed-n075
26	A	Model	Speed-o070
27	A	Model	Speed-p065
28	A	Model	Speed-q060
29	A	Model	MotionStop
30	A	Model	EngIdleB
31	A	Model	MtnStrtB
32	A	Model	DSpeed-1
33	A	Model	DSpeed-2
34	A	Model	DSpeed-3
35	A	Model	MotionStopB
36	A	Model	TankFire
37	A	Model	Welcome

Module B

File No. Description
001 gun elevation

Sound Sets

Latest sound sets for Asp can be downloaded here. Note: These files below are disk image files and require writing to 2GB micro SD Cards using appropriate Disk Imaging software (Active @ Disk Image Freeware is what these files were created with)

Tiger 1
Module A [1]
Module B [2]

T-34
Module A
Module B

IR Battle Capability

Details of the IR functions of the MAKO chip