[phpBB Debug] PHP Warning: in file [ROOT]/includes/bbcode.php on line 379: preg_replace(): The /e modifier is no longer supported, use preg_replace_callback instead
[phpBB Debug] PHP Warning: in file [ROOT]/includes/bbcode.php on line 379: preg_replace(): The /e modifier is no longer supported, use preg_replace_callback instead
[phpBB Debug] PHP Warning: in file [ROOT]/feed.php on line 173: Cannot modify header information - headers already sent by (output started at [ROOT]/includes/functions.php:3823)
[phpBB Debug] PHP Warning: in file [ROOT]/feed.php on line 174: Cannot modify header information - headers already sent by (output started at [ROOT]/includes/functions.php:3823)
RC Tanks Australia Forum Remote Controlled Tanks Australia 2016-02-23T07:09:28+10:00 http://rctanksaustralia.com/forum/feed.php?f=82&t=996 2016-02-23T07:09:28+10:00 2016-02-23T07:09:28+10:00 http://rctanksaustralia.com/forum/viewtopic.php?t=996&p=4283#p4283 <![CDATA[Re: Smoke generator mod.]]>
With the ASP it will be proportional too, right? I'll probarbly buy me one for my birthday :D

Statistics: Posted by Rad_Schuhart — Tue Feb 23, 2016 7:09 am

]]> 2016-02-23T06:31:13+10:00 2016-02-23T06:31:13+10:00 http://rctanksaustralia.com/forum/viewtopic.php?t=996&p=4282#p4282 <![CDATA[Re: Smoke generator mod.]]> The hair dryer element is a good idea :idea:


Cheers
Gra :)

Statistics: Posted by Gra — Tue Feb 23, 2016 6:31 am

]]> 2016-02-23T01:28:28+10:00 2016-02-23T01:28:28+10:00 http://rctanksaustralia.com/forum/viewtopic.php?t=996&p=4281#p4281 <![CDATA[Re: Smoke generator mod.]]>
At the end I replaced the original nicrome wire with a small hairdryer filament and I got LOADS of smoke






Hope it helps somebody.

Statistics: Posted by Rad_Schuhart — Tue Feb 23, 2016 1:28 am

]]> 2015-06-13T17:51:27+10:00 2015-06-13T17:51:27+10:00 http://rctanksaustralia.com/forum/viewtopic.php?t=996&p=3759#p3759 <![CDATA[Smoke generator mod.]]> http://www.hobbyking.com/hobbyking/stor ... e_Car.html

It was working fine for about ten minutes until for some reason I blew the Rx18 smoke transistor. To check that the smoke generator was still working I connected it to the turret rotation's port and the smoke generator was fine. I did this video when connected to that port: https://www.youtube.com/watch?v=AGIZcljQqU8





Do you know why it blew that transistor?

I opened it to see how it was going inside, and unfortunally I broke the nichrome heating filament.

So I decided to replace it with a resistor. So could you please recommend me what kind of resistor should I use? I have no idea of how many ohms and watts I have to use. Also I think I should reduce the volts to the fan, it is a 5v fan powered by a 7.4 lipo battery, so what resistor should I install in the fan?

Thank you very much for your help, I'll really apreciate it.

Statistics: Posted by Rad_Schuhart — Sat Jun 13, 2015 5:51 pm

]]>