Cheers
Gra
Statistics: Posted by Gra — Sun Feb 14, 2016 11:10 am
]]>
]]>
Statistics: Posted by Phyrephish — Thu Dec 04, 2014 6:57 am
]]>
Statistics: Posted by Spudkopf — Mon Dec 01, 2014 10:03 am
]]>
Cheers
KG
Statistics: Posted by Phyrephish — Sun Nov 30, 2014 8:44 pm
]]>
At rest.....
.....and recoiled
Following are some exploded views of this current iteration of the components.
Statistics: Posted by Spudkopf — Thu Nov 27, 2014 8:01 am
]]>
At rest.....
.....and recoiled
Looking at the above it occurs to me that I may have to consider moving the servo mounts further back to make the entire movement sequence more centreline centric?
Statistics: Posted by Spudkopf — Wed Nov 26, 2014 8:45 am
]]>
However I have also still been working on my recoil unit design and have been looking at ways to make it a more universal solution, among these is an idea to created an additional pivot cradle for the existing design, this is to allow the design to be used to replace not only HL StuG style units but also HL standard recoil and BB units as well.
With this I would then also be able to convert my Panther, Leopard, etc.......
Statistics: Posted by Spudkopf — Wed Nov 26, 2014 7:31 am
]]>
Statistics: Posted by Spudkopf — Fri Nov 21, 2014 11:22 am
]]>
Statistics: Posted by Spudkopf — Thu Nov 20, 2014 1:53 pm
]]>
Upon opening the package I was delighted to find a not so unexpected servo, along with some other goodies as well, so many, many thanks to KG for lifting my mood. Now I had planned to reciprocate the surprise by building a CAD model of the new servo this morning before work started, however upon arrival at work I discovered that for some brain fail based reason that I had failed to pack both my work and lunch (breakfast) bags into the car, but instead had only managed to pack my gym bag, so not am I only feeling quite hungry at the moment but also a tad miffed.
Last night I did however manage (with a little trepidation) to install the self centring mod into my Turnigy 9X, I had a bit of a win here as the HL controller I randomly chose to sacrifice to the cause just so happened to have a spare spring floating around inside its guts, although I must say that happy feeling of this win was somewhat short lived and almost fully offset by the fact the screws holding the Turnigy 9X together are far from the most robust of screws and I have come very close to stripping out the heads of about 50% of them.
The situation was not aided by the fact that after I had put the controller back together I received a switch error message, not knowing any better I pulled the unit apart again to make sure everything was as it should be, only to later realise that the error was actually being caused by a thrown switch, and thus I had to reassemble the unit with these now already rather dodgy screws for a second time.
Now all I have to do is get the damn thing programmed for tanks and I’ll be set to move on to the next level.
I will PM you (KG) later today about the third and forth items in the package
Now in regards to $tuG progress, this is slow as usual but at the moment I’m working on making a replacement of the missing inspection/access port located on the lower rear hull plate, it’s quite surprising and a great pity that there does not appear to be an after market replacement available for such a prominent detail, sadly it goes without saying that if I had 3D printer access, I could knock up a CAD model of this missing item in minutes.
Talking CAD, the modelling of the recoil unit goes on, I have spent much of the recent time deleting redundant geometry and generally refining component design overall, thus far this work has only been applied to both revisions of the short version of the recoil unit, but I will push the same refinements onto the original design as well soon.
I will try and post some progress images either today or tomorrow time permitting.
Statistics: Posted by Spudkopf — Thu Nov 13, 2014 9:37 am
]]>
Here are some images of Revisions 0 and 1 of the short recoil unit (stripped back to main components) and some basic (recoiled) dimensions:
Rev. 0
Rev. 1
Recoiled Dimensions
Statistics: Posted by Spudkopf — Tue Nov 11, 2014 1:40 pm
]]>
Also added the shield/hatch lock (again sorry about the pic quality.....
Statistics: Posted by Spudkopf — Sun Nov 09, 2014 4:23 pm
]]>
After scouring through all my references I've found an image of the StuG at Aberdeen Proving Ground that show remnants of the chains, that appear to be connected via a ring through a hole drilled into the top inside of the hitch horn castings.
Statistics: Posted by Spudkopf — Sat Nov 08, 2014 11:00 am
]]>
and so as an alternative here is recoil unit Mk II (or short)
..... just giving myself options
Statistics: Posted by Spudkopf — Fri Nov 07, 2014 4:03 pm
]]>